Tsm library slots
TS supports storage-only library frames with high-density slots that can significantly increase a library’s total capacity yet reduce the physical footprint. If the number this command produces looks to be too low, you can use the SHOW SLOTS LIBRARY_NAME command to examine what is in the . TSM - Library Tape Management Moving Tapes offsite Freeing up library slots Reclaiming offsite tapes Reclaiming tapes that are assigned to another TSM server.
Library slot count manipulation in TSM
While it is possible to remove or insert an entire 15 slot magazine, this is usually inconvenient, time consuming and requires careful tracking of the cartridge locations. Please note, pressing with firm pressure rather than jabbing or pushing hard works best. If you have lots of tapes to input to TSM you can power your library down, open the main door, then just put the tapes directly into empty libary slots. To checkin a volume that no longer has valid data on it, to the scratch pool, use the form: SHOW MP Useful for determining which volume is in-use by a given mount point and other attributes for the assigned mount points. Press the magazine access button for the desired magazine. A tape with valid known to TSM data is checked into the library, the following format is used:
IBM TS3310 Tape Library
Be aware that some of these commands are resource intensive and cannot be cancelled and some commands will try to fix problems; that is they may UPDATE the TSM database. If possible, try the commands on a test system before you use them in production. In general, you should not run SHOW commands unless you are familiar with that particular command, or TSM support personnel have asked you to run them.
Many of the older show commands are now official, as they have equivalent 'display' or 'validate' commands. This is not an exhaustive list of SHOW commands because I do not know them all I have missed out some obscure commands that is, the ones that I don't understand The list is split into 6. Client Commands Client commands can produce a lot of output that will scroll off the screen, so you may prefer to pipe them into a file.
This command will tell you which one is in use for this client. The client and server report and negotiate the capabilities that each has when a session is started by a client to a server. This show command reports the capabilities available by this server and client. You use this command to find out what plug-ins are available for this client. TSM knows what parts of a file have changed, by storing checksum information in a cache file on the client.
This command will display information about the subfile cache, if the client is configured to use subfile backup. Server commands Simply displays the server date and time. This command could be worth running as a diagnostic data gathering exercise in a problem situation.
177. As I fingered her, she wanked me off brutally, showing no mercy for this young and inexperienced penis. She said, "My name's Cassie". Forget all your worries and come to me. She was dressed in this tight miniskirt and was wearing a very tight t shirt that displayed these lovely tits nicely. but you are welcome back here ANYTIME!".
Virtual Tapes Freeing up library slots If your library becomes full, you may need to free up some slots. The trick is to eject older tapes from the library that you are not likely to use for a while, and keep the active tapes in the library. We can 'move' tapes outside of the library to a nearby 'location', but the tapes are still considered as mountable. When processing an manual mount request, you must use the 'Checkin Libvol' command to update the library inventory and tell TSM that the tape is back in the robot since that is ultimately how the tape gets mounted.
TSM will automatically toggle the volume's access mode from ReadOnly to ReadWrite and back again as it is moved in and out of the library. This is to allow any read operations to proceed e. Re-generating a library definition Sometimes, especially with TSM servers hosted on Windows, it is necessary to delete and redefine a tape libary.
After you remove the tape paths, you have to delete the library itself to remove the TSM server library inventory. Once you re-define the library and paths, you need to re-generate the library inventory by running the following commands, which must be run in the sequence shown. You place your new cartridges into the IO station then run a checkin command. The syntax of the command varies slightly depending on what type of library you have. However be aware that the robot will select the first tape from the IO station, it will not scan the IO station for your tape.
I've had the Library Manager tell me the IO station was empty apart from a specific tape that I wanted, yet TSM kept selecting an incorrect tape on checkin. Eventually I tried a bulk checkin and then discovered there was four foreign tapes in the IO station. If you have lots of tapes to input to TSM you can power your library down, open the main door, then just put the tapes directly into empty libary slots.
This is done by partitioning the library into several logical libraries. If a volume has been removed from the library, but TSM has not been informed you can clear it from TSM with the command below. These options are set using the library interface from the Drives, Cleaning Mode panel.
Manage Many Apps with Tabs We often find ourselves in front of our machines with many applications running at the same time. If you need to switch apps quickly, sometimes it can be frustrating to try and navigate through your dock bar to find what you need. Your dock likely contains icons for many programs you frequently use, a few icons Apple requires in the dock that cannot be removed, and will also store icons for any program that is currently open, even if you haven't added that program to the dock for easy access.
If you're running a lot of applications, your dock can very quickly become large and cluttered. Command Tab - A quick way to get your apps under control without having to search through your entire dock is to hold down the Command key, then press the Tab key. This will open up the "mini-dock," or Application Switcher, with only your active apps, and now you can move through your open applications more quickly than trying to navigate your full dock. Navigate by Mouse - you can simply use your mouse to scroll through the mini-dock and hover over the correct icon to select the app you want, then either release the Command button or click the app icon to pull it up.
Navigate by Keyboard - you can continue to hold the Command key and press the Tab key to move through the list. When you've selected the app you want, simply let go of the Command key and you will switch to that app. You can also navigate back and forth through the mini-dock using your left and right arrow key - helpful if you need to back up a few icons to select your desired app, because using the tab key will only tab forward through the list.
Manage Your Apps from the Switcher You can also quickly manage your apps from this screen. The modern iMacs make it easy to work hard and play hard, letting us install and run multiple applications and multi-task with just a few clicks.
When you work and play on one machine, it's easy for your desktop to get out of control with way too many files, programs, and other icons cluttering it all up. An easy trick to clean it up quickly is to group some of your icons together in a desktop Folder. Then you can access that Folder from your desktop when you need those icons and keep them in easy reach, but also keep your desktop simple, clean, and uncluttered.